Bryant 355CAV User Manual Page 11
- Page / 62
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
11
PLUG
CAP
COLLECTOR BOX
DRAIN TUBE (BLUE &
WHITE STRIPED)
INDUCER HOUSING
(MOLDED) DRAIN
TUBE (VIOLET)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
DRAIN TUBE (BLUE)
COLLECTOR BOX
TUBE EXTENSION
CONDENSATE
T
RAP
COLLECTOR BOX
TUBE (GREEN)
A07276
Fig. 9 -- Downflow Tube Configuration
(Left--hand Trap Installation)
DOWNFLOW APPLICATIONS
A downflow furnace application is where furnace blower is located
above combustion and controls section of furnace, and conditioned
air is discharged downwards.
Condensate Trap Location
The condensate trap must be removed from the factory--installed
blower shelf location and relocated in selected application location
asshowninFig.2,9,or10.
To relocate condensate trap from the blower shelf to desired
location, perform the following:
1. Remove three tubes connected to condensate trap.
2. Remove trap from blower shelf by gently pushing tabs
inward and rotating trap.
3. Remove casing hole filler cap from casing hole. (See Fig. 2
and 10.)
4. Install casing hole filler cap (factory--supplied in loose parts
bag) into blower shelf hole where trap was removed.
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal
injury or death.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the equipment
room.
!
WARNING
5. Install condensate trap into left--hand side casing hole by
inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.
6. Fill unused condensate trap casing holes with plastic filler
caps (factory--supplied in loose parts bag).
CAP
PLUG
COLLECTOR BOX
DRAIN TUBE (BLUE &
WHITE STRIPED)
INDUCER HOUSING
(MOLDED) DRAIN
TUBE (VIOLET)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
DRAIN TUBE (BLUE)
COLLECTOR BOX
TUBE EXTENSION
CONDENSATE
TRAP
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX
EXTENSION
DRAIN TUBE
DRAIN TUBE
COUPLING
A07277
Fig. 10 -- Downflow Tube Configuration
(Right--Hand Trap Configuration)
Condensate Trap Tubing
NOTE: See Fig. 9 or 10 or tube routing label on main furnace
door to check for proper connections.
1. Collector Box Drain Tube
a. Remove factory--installed plug from LOWER collector
box drain tube (blue and white striped label).
b. Install removed clamp and plug into UPPER collector
box drain tube (blue label) which was connected to
condensate trap.
c. Connect LOWER collector box drain connection to
condensate trap.
(3.) Condensate Trap Located on Left Side of Casing
a. Connect LOWER collector box drain tube (blue
and white striped label) to condensate trap. Tube
does not need to be cut.
b. Clamp tube to prevent any condensate leakage.
(4.) Condensate Trap Located on Right Side of Casing
a. Install drain tube coupling (factory--supplied in
loose parts bag) into collector box drain tube
(blue and white striped label) which was
previously plugged.
b. Connect larger diameter drain tube
(factory--supplied in loose parts bag) to drain
tube coupling, extending collector box drain
tube for connection to condensate trap.
c. Route extended collector box drain tube between
gas valve and inlet housing as shown in Fig. 10.
d. Determine appropriate length and cut.
e. Connect to condensate trap.
2. Inducer Housing Drain Tube
a. Remove factory--installed cap and clamp from LOWER
inducer housing drain connection.
355CAV
355CAV
- Installation Instructions 1
- IMPORTANT 2
- TABLE OF CONTENTS 3
- SAFETY CONSIDERATIONS 3
- 80 / 27 C 6
- CODES AND STANDARDS 7
- ELECTROSTATIC DISCHARGE (ESD) 7
- PRECAUTIONS 7
- INTRODUCTION 7
- APPLICATIONS 7
- UPFLOW APPLICATION 8
- Orientation) 9
- DOWNFLOW APPLICATIONS 11
- HORIZONTAL LEFT (SUPPLY--AIR 12
- DISCHARGE) APPLICATIONS 12
- ″ (146 mm) 13
- HORIZONTAL RIGHT 15
- LOCATION 16
- Hazardous Locations 17
- INSTALLATION 18
- AIR DUCTS 21
- WASHABLE 22
- FRONT FILLER 23
- GAS LINE 24
- VENT PIPE 24
- Electrical Connections 25
- 115--v Wiring 25
- J--Box Relocation 26
- 24--v wiring 26
- Fig. 33 -- Furnace Control 30
- Abandoned masonry 33
- (per code) 33
- COMBUSTION AIR PIPE 34
- (304.8mm) 37
- 3” (76.2mm) 38
- minimum 38
- VENT TERMINATION 39
- Direct Vent (2--Pipe Only) 42
- CONDENSATE DRAIN 43
- Step 1 — General 44
- Fig. 49 -- Wiring Diagram 46
- Cooling Mode 50
- Thermidistat Mode 50
- Step 4 — Adjustments 54
- * Orifice numbers shown in 56
- are factory-installed 56
- U.S.A. Only 57
- BURNER FLAME 58
- MANIFOLD 58
- Set Temperature Rise 59
- CHECKLIST 60
- CHECKLIST — INST ALLATION 61
- Catalog No. II355CA 62
- --- 0 6 0 --- 5 62
Related products and manuals for Kiln Bryant 355CAV
Kiln Bryant A10252 User Manual
(10 pages)
(10 pages)
Kiln Bryant SERIES A 355CAV User Manual
(62 pages)
(62 pages)
Kiln Bryant 330AAV User Manual
(12 pages)
(12 pages)
Kiln Bryant 373LAV EN User Manual
(12 pages)
(12 pages)
Kiln Bryant 396HAD User Manual
(8 pages)
(8 pages)
Kiln Bryant 312AAV User Manual
(30 pages)
(30 pages)
Kiln Bryant 367RAN User Manual
(8 pages)
(8 pages)
Kiln Bryant 355MAV EN User Manual
(44 pages)
(44 pages)
Kiln Bryant Gas 340MAV User Manual
(48 pages)
(48 pages)
Kiln Bryant 3Model 383KAV User Manual
(12 pages)
(12 pages)
Kiln Bryant 333BAV User Manual
(12 pages)
(12 pages)
Kiln Bryant 312AAV/JAV User Manual
(56 pages)
(56 pages)
Kiln Bryant 340MAV User Manual
(12 pages)
(12 pages)
Kiln Bryant 359BAV User Manual
(8 pages)
(8 pages)
Kiln Bryant 367AAN User Manual
(8 pages)
(8 pages)
Kiln Bryant 373LAV User Manual
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.448 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals