Bryant DuraPac Series 580f User Manual download pdf (Page 58)

—58—

APPENDIX A — ECONOMI$ER+ LABEL

Button

DS1

(Red)

DS2

(Yellow)

DS3

(Green)

DS4

(Green)

Action flash flash flash flash

Note 1

Indicators flash in sequence at .5 sec intervals

Names HB ECONO Y1 Y2

Actions flash flash steady steady

Note 1 Heartbeat Indicator flashes to indicate proper operation of the control

Note 2 Econo indicator flashes to indicate free cooling being used

Note 3 Y1 and Y2 are on steady when a call thermostat Y1 and Y2 are closed

Note 4 ERROR - HB and Econo are on steady to indicate the presence of an error

Names READ ADV SET NO I/O NO

TEN'S

OR ON

ONES OR

OFF

Actions Push Push flash, no flash no flash no flash no

Note 1 Push and release the READ button to enter Read Mode. The SET NO Indicator flashes once

to indicate the setup point is selected for viewing

Note 2 Push and release ADV button repeatedly to advance to the desired setup point or I/O point

Each time the ADV button is pushed, the SET NO flashes the point number until the desired

I/O point is reached and then the I/O NO flashes the I/O point no.

Note 3 After the SET NO indicator identifies the desired point no, push and release the READ

button to display the value in the TEN's and ONE's indicator (i.e., 5 flashes for a value of 5)

or a steady TEN's indicator for an on and a steady ONE's for off.

To aid in counting, values of 5 are flashed in groups of 5 (i.e., 150 = 3 groups of fast 5 flashes)

and then follow by balance in slow flashes (i.e., 7 = 5 quick flashes + 2 slow flashes)

Note 4 Setpoint values are displayed first followed by I/O values and then back to Setpoint values

Red Set No LED displays Setup item numbers, and Yellow I/O LED displays I/O item no

Note 5 Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit

MODE OF OPERATION

READ MODE

PUSHBUTTONS LED INDICATORS

STARTUP MODE

RUN MODE

Button

DS1

(Red)

DS2

(Yellow)

DS3

(Green)

DS4

(Green)

Names ADJUST ADV SET NO SETUP

TEN'S

OR ON

ONES OR

OFF

Actions Hold/Push Push flash, no steady flash no flash no

Note 1 Push and hold the ADJUST button until the SETUP indicator turns on.

Note 2 Push and release ADV button repeatedly to advance to the desired setup point.

Each time the ADV button is pushed, the SET NO flashes the point number and then displays

the current setting

Note 3 Once the current value has been displayed the TENS indicator will turn on steady and while it

on use the ADJUST button to enter the value. (i.e., push the button 4 times to enter 4)

Then wait for the ONES indicator to turn on and enter the ONES setting

Wait for indicator to turn off and then push read/adjust to check the setting

Note 4 Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit

Names ADJUST MAN MAN I/O NO

TEN'S

OR ON

ONES OR

OFF

Actions Push Hold/Push steady flash no flash no flash no

Note 1 Push and hold the MAN button until the MAN indicator turns on.

Note 2 Push and release MAN button repeatedly to advance to the desired I/O point.

Each time the MAN button is pushed, the I/O NO flashes the I/O point number.

Note 3 After the desired I/O No is reached push and release the ADJUST to toggle the output on

and off or open and closed

Note 4 Routine exits after 10 min of no activity or push and hold button 1 and 2 for 3 seconds to exit

PUSHBUTTONS LED INDICATORS

SETUP MODE

MANUAL

MODE OF OPERATION

I/O POINTS

NO I/O Points UNITS

1 C1 Output -

2 C2 Output -

3 C3 Output -

4 C4 Output -

5 Economizer Damper Output %

6 Supply Air temperature F

7 Outside Air temperature F

8 Return Air Temperature F

9 Indoor Relative Humidity %

10 Outdoor Relative Humidity %

11 Indoor Air Quality PPM

12 Remote Minimum Position %

13 Y1 Status (next version) -

14 Y2 Status (next version) -

15 G Status (next version) -

16 Occ Status (next version) -

ALARM CODES

NO DESCRIPTION

1 SAT sensor invalid

2 RAT Sensor Invalid (only with changeover type 3&5)

3 OAT Sensor Invalid

4 ORH Sensor invalid (only with changeover type 3&4)

5 IRH Sensor invalid (only with changeover type 5)

6 IAQ Sensor Invalid (only if IAQ=1)

7 Y2onY1off

8 Micro Fails E2 test

note 1 Micro Fails RAM test

note 2 Micro Fails ROM test

Note 1 DS1+DS3/DS2+D4 will alternately flash

Note 2 DS1+DS2/DS3+D4 will alternately flash

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 64

Comments to this Manuals

No comments

Bryant DuraPac Series 580f User Manual Page 58

Comments to this Manuals

Related products and manuals for Radiators Bryant DuraPac Series 580f