Bryant SYSTXBBECW01 Instruction Manual Page 38
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
28
6.3.1.1. Auto Mode set up
Once the auto changeover option has been selected, touch SAVE.
S Enable or Disable: Choose to enable or disable auto changeover mode
d Default = Enable
S Auto changeover time: Adjustable from 5 to 120 minutes
d Default = 30 minutes
6.3.1.2. Heat/Cool Deadband
The minimum difference enforced between heating and cooling desired
temperatures. The deadband does not change when the user changes between
Fahrenheit (_F) and Celsius (_C). Ex: A 2_ deadband will be 2_For2_Canddoes
not change with units, _Fand_C. This can allow one setting to “push” the other to
maintain this difference. When the correct deadband is set, touch SAVE.
S Deadband: Adjustable from 0 to 6_ F
d Default = 2_
6.3.1.3. Offsets
This option allows calibration (or deliberate miscalibration) of the temperature and
humidity sensors. These offsets are added to the actual temperature/humidity
values. When the correct offsets are made, touch SAVE.
S Outdoor temperature: Adjustable from --5 to 5_F(--3to3_C)
d Default = 0_F
S Humidity: Adjustable from --10 – 10%
d Default = 0%
- Installation Instructions 1
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont.) 4
- 1. Safety Considerations 11
- 2. Introduction 11
- 3. Quick Start 12
- 3.1. Set Time and Date 12
- 3.1.2. Setup Time Zone 14
- 3.2. Set Dealer Information 15
- 4.2. Check Equipment 16
- 4. Installation 16
- 4.1. Overview 16
- 4.3. Location 17
- 4.3.1. Wall Control 17
- 4.3.2. Remote Room Sensors 18
- 4.4. Wiring Considerations 19
- 4.4.1. Shielded Wire 22
- 4.5. Mounting 23
- 4.5.1. Decorative Backplate 24
- 4.6. Humidifier Connections 25
- 4.6.1. Bypass Humidifier 25
- 5. Commissioning 26
- 5.7. Filter Type Selection 31
- 5.8. Humidifier Installation 31
- 5.10. Equipment Summary 31
- 6. Service Menu 34
- 6.1. Equipment Summary 35
- 6.2. Installation 35
- 6.3. Set up 36
- 6.3.1. Thermostat 37
- 6.3.1.1. Auto Mode set up 38
- 6.3.1.2. Heat/Cool Deadband 38
- 6.3.1.3. Offsets 38
- 6.3.1.5. Scheduling Enable 39
- 6.3.2. Fan Coil 39
- 6.3.2.1. Airflow 40
- 6.3.2.2. Altitude 41
- 6.3.2.4. Fan Coil G--Terminal 42
- 6.3.3. Furnace 44
- 6.3.3.1. Furnace Airflow 45
- 6.3.3.2. AC/HP Air Flow 45
- 6.3.3.3. Furnace Staging 46
- 6.3.3.5. Furnace Off Delay 47
- 6.3.3.6. Altitude 47
- 6.3.3.8. Furnace G Terminal 48
- 6.3.4. AC/Heat Pump 50
- 6.3.4.1. Latching 50
- 6.3.4.2. Cooling Lockout 51
- 6.3.4.3. Defrost Interval 52
- 6.3.4.4. Low Ambient Cooling 52
- 6.3.4.5. Quiet Shift 52
- 6.3.4.6. AC/Heat Pump RPM Max 53
- 6.3.4.7. Defrost Fan Delay 53
- 6.3.4.8. Brownout Disable 53
- 6.3.4.9 Low Air Multiplier 53
- 6.3.5. Heat Source Lockout 54
- 6.3.7. Zoning (If Applicable) 55
- 6.3.7.1. Zoning Disable 55
- 6.3.7.2. Zone Offsets 56
- 6.3.7.3. Zone Airflow Limits 56
- 6.3.7.4. Duct Assessment Time 56
- 6.3.8. Accessories 57
- 6.3.8.1. Filter 57
- 6.3.8.2. Humidifier 58
- 6.3.8.3. Ultraviolet Lights 58
- 6.3.8.4. Ventilator 58
- 6.3.9. Utility Curtailment 59
- 6.3.10. Hydronic Airflow 59
- 6.4. Check out 60
- 6.4.1. Electric Heat 61
- 6.4.2. Furnace 61
- 6.4.3. Hydronic 62
- 6.4.4. Air Conditioning 62
- 6.4.5. Heat Pump Heating 63
- 6.4.6. Heat Pump Cooling 64
- 6.4.7. Humidifier 64
- 6.4.8. Ventilator 65
- 6.4.9. Zoning (If Applicable) 65
- 6.4.9.1. Airflow Limits 65
- 6.4.9.2. Damper/Sensor Check 65
- 6.4.9.3. Zone Duct Assessment 66
- 6.4.9.4. Sensor Type 66
- 6.5. Service Information 66
- 6.5.1. Advanced Diagnostics 67
- 6.5.2. Fan Coil Status 67
- 6.5.3. Furnace Status 68
- 6.5.4. AC Status 68
- 6.5.5. Heat Pump Status 69
- 6.5.6. Zoning Status 69
- 6.5.7. Last 10 System Events 70
- 6.5.8. Run/Fault History 71
- 6.5.9. Model/Serial Numbers 71
- 6.5.10. Service Phone Number 72
- 6.6.1. Charging 73
- 6.6.2. Pump down 74
- 6.6.3. Evacuation 74
- 6.7.1. Charging 75
- 6.7.2. Pump down 77
- 6.7.3. Evacuation 77
- 6.7.4. EXV Position 78
- 6.8. Dealer Logo 78
- 6.9. Utility Event Setup 79
- 7.0 Wireless Set--up 80
- Connected: 84
- Not Connected: 84
- SSID & Security Key 86
- User Interface 89
- Communicating 89
- AC or HP* 89
- Variable-Speed 89
- Furnace/ Fan Coil 89
- Furnace/Fan Coil 90
- Fan Coil 91
- Humidifier 92
- Connection 92
- (Optional) 92
- 1-Stage AC 93
- 1-Spd. HP 94
- FE Fan Coil or 95
- Variable Speed Furnace 95
- NOTES (Cont.) 98
Related products and manuals for Recording Equipment Bryant SYSTXBBECW01
(40 pages)© 2020, manymanuals.com. All rights reserved. | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals